Gurugram
08048034240
Which Hawker Traction Battery Fits Your Battery Manufacturer Requirements

A correct replacement must match more than the forklift’s voltage. You will be able to turn the machine, battery compartment, duty cycle, charger, and compliance records into a written specification that identifies the right Hawker technology and exposes an unsuitable quotation.

Key takeaways

  • Photograph the truck, battery and charger nameplates before requesting a quotation.
  • Confirm voltage, dimensions, connector, polarity, lifting points and compartment clearance.
  • Select battery technology according to duty cycle, charging time and operating conditions.
  • Specify capacity, charger settings, documentation and service access in the purchase request.

Start with the truck, compartment, and nameplate—not the brand

A correct brand name does not make a replacement fit. Before requesting a quotation for Hawker traction batteries in Gurugram, photograph the truck nameplate, original battery nameplate, charger nameplate, and battery compartment.

1. Record the truck or machine make, model, serial number, and manufacturer’s battery specification. Capture nominal voltage, cell count, Ah capacity, charging current, connector type, polarity, and the original battery’s model number.

Common packs use 24, 36, 48, 72, or 80 volts, usually built from 2-volt cells; changing cell count can damage the traction controller or charger.

2. Measure the compartment, not just the old battery. Provide tray length, width, height, roller arrangement, retaining hardware, cable-exit position, terminal location, lifting points, and permitted battery mass. The wrong connector, polarity, or cable route can stop a correctly rated battery from being usable.

3. Describe the work pattern: hours per shift, shifts per day, typical load, travel distance, peak lifting periods, pauses for charging, and charging-room ambient temperature. State whether the room has ventilation and whether watering access is available.

4. Ask the supplier to separate battery price from charger changes, delivery and lifting, commissioning, watering equipment, maintenance, emergency response, spent-battery collection, and recycling records. Request stated compliance with applicable IS 1651 provisions, IEC 60254 tests, installation ventilation rules, and India’s Battery Waste Management Rules.

Judge the quotation by documented fit, service scope, and lifecycle effort—not the Hawker name alone.

Define “fits” across electrical, mechanical, and operating limits

Compatibility is a pass/fail check, not a brand match. A Hawker battery is suitable only when its electrical values, physical dimensions, charger requirements, and operating limits all agree with the vehicle and its manual.

Compare the original battery nameplate, truck specification, and charger nameplate for:

  • Nominal voltage and cell count. Common packs use 24, 36, 48, 72, or 80 V; changing the cell count can damage the traction controller or charger.
  • Ampere-hour rating, charging current, and charging profile. A correct voltage does not make an incompatible charger safe.
  • Tray length, width, height, permitted battery mass, and roller arrangement. A pack that cannot be restrained is not a replacement.
  • Terminal position, polarity, connector type, cable exit, and lifting points. A wrong connector or cable route can prevent connection or create a short circuit.

Then test the duty cycle. Confirm that the battery supplies the required daily energy for travel, lifting, acceleration, hydraulic work, idle periods, and charger losses without exceeding the manufacturer’s permitted depth of discharge. Check discharge rate, heat generation, ambient temperature, ventilation, watering access, and charging-window limits.

This is where hawker battery options for industry separate: flooded tubular, TPPL or AGM-style valve-regulated, and lithium-ion systems use different charging, ventilation, maintenance, and temperature rules. Request the exact model datasheet, charger settings, dimensional drawing, mass, connector layout, and compliance documents before approval. A nameplate reading “Hawker” proves identity, not compatibility.

Choose the battery technology for the duty cycle and charging window

A flooded tubular battery suits long shifts with planned charging, while TPPL or AGM-style valve-regulated and lithium-ion systems suit tighter charging windows. Choose by operating pattern, charger approval, ventilation, temperature and labour—not by the Hawker name alone.

OptionBest fitRequirements and trade-offs
Flooded tubular lead-acidHeavy, predictable duty with time for a full charge and battery changeLowest acquisition cost in many fleets, but requires watering, equalisation, hydrogen ventilation, acid-resistant flooring and safe lifting. Specify permitted charging temperature and temperature-compensated charging where required.
TPPL or AGM-style valve-regulatedMulti-shift work with limited maintenance space and approved opportunity chargingNo routine watering, but it is not a flooded battery without caps. Use the exact TPPL charger profile; a wet-cell setting can cause undercharge, gassing, thermal stress and early capacity loss.
Lithium-ionRepeated short charging windows, high utilisation and operations that cannot spare time for watering or battery swapsOpportunity charging works only with an approved battery-charger combination. Confirm battery-management controls, charging temperature limits, thermal protection, service access and recycling arrangements.

Treat the charging room as part of the specification. Flooded cells need ventilation calculated from charging gas evolution, plus ignition control, emergency isolation and an eyewash station; high Gurugram summer temperatures and poor airflow accelerate lead-acid ageing.

Ask the supplier to state the approved charger, charging current, ambient and charging temperature range, permitted opportunity-charging pattern, expected daily energy use and total maintenance scope. This is the practical difference among Hawker battery options for industry—and the point where a cheap battery can become an expensive mismatch.

Match capacity and charger settings to real daily energy use

An 800 Ah nameplate does not mean 800 Ah is available during every shift. Size the battery from daily energy removed, then divide that requirement by the manufacturer’s permitted depth of discharge. Include operating hours, average current, travel distance, lifting and hydraulic demand, acceleration peaks, idle periods, and charger losses.

A battery that is too small reaches low voltage early, heats faster, and loses service life.

Record these figures before selecting capacity:

  • Amp-hours removed per shift from the truck’s monitor or a measured discharge test
  • Peak travel, lift, and hydraulic current, because voltage sag can trip the truck before the nominal capacity is exhausted
  • Ambient temperature, cold-store exposure, floor gradient, load weight, and shift length
  • Available charging hours, charger output current, charging profile, and mains capacity
  • Battery mass permitted by the truck and the space available for heat dissipation

Match the charger to the battery, not merely to its voltage. A TPPL or AGM-style battery needs the profile specified for that product; a conventional wet-cell setting can cause chronic undercharge, gassing, thermal stress, or early capacity loss.

Opportunity charging works only when the battery and charger are approved as a combination, with controls for temperature and excessive state-of-charge. For hawker traction batteries in gurugram, require the supplier to state the recommended charger voltage, current, profile, and allowable depth of discharge in writing.

Then verify the installed charger nameplate against those values before commissioning.

Write a Gurugram supply specification that can be accepted and serviced

Before delivery, require documentary proof, a witnessed acceptance test, and a service plan that remains valid until end-of-life collection. For a Hawker traction battery for battery manufacturer requirements in Gurugram, do not treat the brand name as compliance evidence.

1. State the equipment make and model, compartment dimensions, nominal voltage, Ah capacity, permitted weight, connector and polarity, cable-exit position, lifting points, and tray or roller arrangement. Record cell count separately; 24 V, 36 V, 48 V, 72 V, and 80 V packs are not interchangeable.

2. Ask the vendor to identify compliance separately: applicable IS 1651 provisions, IEC 60254 test results, installation ventilation and electrical-safety requirements, and Battery Waste Management Rules obligations. Request certificates, test reports, and disposal-registration evidence by document number.

3. Require the manufacturing date, complete serial-number and cell or module traceability, terminal details, connector drawing, delivery state of charge or electrolyte condition, safety data, charger settings, warranty exclusions, and a signed capacity or discharge acceptance test. Open-circuit voltage alone is insufficient for a large pack.

4. Price the battery separately from the charger, delivery and lifting, commissioning, watering kit, preventive maintenance, emergency response, spent-battery collection, and recycling records. This exposes a low quote that creates charger upgrades or excessive watering labour.

5. Define life-cycle service: approved distilled or de-ionized water, equalization intervals, response times, inspection records, and replacement rules. Never mix old and new units or unequal chemistries in one string without written approval.

GLOBAL POWER TECHNOLOGIES can use this traction battery manufacturer supply structure to document installation, maintenance, and collection responsibilities for a Gurugram site.

Related product

Hawker Traction batteries

Hawker Traction batteries

Hawker Traction batteries

manufactured by EnerSys, are premium, high-capacity industrial power cells engineered for demanding material handling equipment.

View product →

Frequently asked questions

  • What should you check before ordering a Hawker traction battery?

    Photograph the truck nameplate, original battery nameplate, charger nameplate and battery compartment. Confirm voltage, dimensions, connector, polarity, lifting points and clearance.

  • What does it mean for a traction battery to fit?

    A battery fits when its electrical ratings, physical dimensions, connector and polarity, lifting arrangement, ventilation needs, charger compatibility and operating limits suit the truck.

  • How do you choose the right battery technology for a truck?

    Match the technology to the duty cycle, shift pattern, opportunity-charging access, charging window, maintenance resources and operating environment.

  • How should battery capacity and charger settings be matched?

    Use real daily energy consumption, recharge time and the charger’s voltage and current settings. Do not select capacity from truck size alone.

  • What should a Gurugram traction battery supply specification include?

    State the truck model, battery voltage, capacity, dimensions, connector, polarity, terminal arrangement, charger details, duty cycle, documentation, delivery requirements and service expectations.

Oct 28th, 2026 9:02 AM

Keywords